特斯拉汽車 特斯拉鍍膜 特斯拉 特斯拉隔熱紙 tesla Tesla Thermal paper
|
車身翠光鍍膜流程說明
翠光鍍膜前需要車身外觀檢查
洗車前先檢查車體表面
最近壹個月內有無板金或烤漆
板金烤漆的傷痕深淺狀態確認
Exterior Checking
Checking the body appearance of vehicle has dents or damages before car wash, and making
sure that vehicle has not been baking paint within one month.
洗車
1. 使用高壓噴槍將車體上的砂泥汙漬確實沖洗
2. 將專用清洗劑泡沫均勻噴塗至車身,並使泡沫停留些許時間
3. 用專用海綿將泡沫均勻塗抹車身,確實洗車
4. 洗車後徹底的沖洗車身用乾淨的吸水布輕拭車體
5. 使用噴風機將細微部分的水份完全去除
Car wash
1. Using the high pressure water to wash out the mud and stain.
2. Spraying the professional carwash detergent to whole vehicle for a while.
3. Using the special sponge to clean the vehicle.
4. Washing out the detergent.
5. Using the soft and fine rag to wipe the vehicle.
6. Using the high pressure air nozzle to blow the water out on the vehicle.
鐵粉去除
車身表面因為與環境的長期接觸,而使灰塵與空氣中的細小鐵粉粒附著在車身上,長期下來會因鐵粉的氧化而侵蝕烤漆!!!所以在鍍膜前的鐵粉去除動作是必要且關鍵的工序!!!透過藥劑與專用清洗布的處理,將鐵粉徹底去除
Remove the iron deposits & particles
Using the special chemical removes the iron deposits and particles that could cause the
serious corrosion. This is very important step before coating, because iron deposits and
particles remain on the vehicle that can still corrode the sheet metal after
coating.
局部保護施工
研磨作業施工前,須用紙質膠帶包覆下列部位
1. 未烤漆之塑膠料件部分與燈具周圍
2. 徽飾配件之部位
3. 易產生刮痕之部位
4. 其他研磨時會阻塞之部位
Sealed the chrome parts and
unpainted area
Chrome parts and unpainted area are easy to get the scratches when expert polishing the
vehicle, therefore, they have to been sealed by paper tape before polishing.
研磨作業
研磨作業的主要目的是去除車身烤漆上的傷痕,提升整體車體烤漆之質感與亮度依照車身烤漆之實際狀態而選擇研磨劑種類請選用不含樹脂與蠟成分之研磨劑(若選用含樹脂或蠟之研磨劑,容易造成鍍膜剝落或是條紋現象
Polishing work
Polishing is another key step before coating. Due to the polishing work, it could make the
large different of brightness on the vehicle. If car detailing shop ignores the importance
of polishing, it cannot present the 100% result of car coating.
除油作業
主要目的為去除車身上多餘之油份,可以用專用吸油布來施工,切勿使用會刮傷車烤漆疑慮之布料施做此工法
Degreasing work
The Importance of degreasing is that the unnecessary grease can make negative effect of the
coating chemicals. Using the special cloths to absorb the grease remained on the sheet
metal.
翠光鍍膜施工
完成前面幾項準備作業後,再將GAMA翠光奈米陶瓷鍍膜劑均勻且規律的塗抹於車身表面,待略為乾燥之後,在使用專用超細纖維布完整塗佈整個車身,即完成鍍膜施工
Coating work
After completing previous steps, using GAMA nano ceramic coating treatment equally and
regularly wipe on the vehicle. Once the surface of coating is slightly dry, using the
special ultra-fine fiber cloth cleans whole vehicle to finish the work.
|